K2 BLACK SILICONE BLISTER +350°C 21 GHigh-temp. SiliconeDescriptionHigh quality silicone. Perfectly adapts to the sealed surfaces. High temperature resistant up to 350°C. Meets the requirements of car manufacturers (O.E.M. - Original Equipment Manufacturer).Replaces traditional gaskets: cork, paper, felt, asbestos and rubber. Thanks to the SENSOR SAFE formula, it is safe for lambda sensors used in modern cars with electronic fuel injection.Resistant to oils, greases, coolants etc. It can be used for all car models and makes, among others for sealing: valve covers, thermostat gaskets, oil pans, camshaft covers, water pumps, rear axle covers and many other elements where tightness and high temperature resistance are required.
USE:1. The surface be dry, free from dust, dirt, grease and the remains of an old seal.2. Spread a small amount of silicone on the surface.3. Remove excess using a knife dipped in soapy water.4. The sealant starts drying after 5 minutes, after 1 hour it is resistant to touch. It dries completely after 24 hours.5. Excess solidified silicone can be removed with a sharp tool.6. Close the tube after each use.
BLACK SILICONE 21g - Silicone gioăng máy chịu nhiệt độ cao 350 độ CMô tả:BLACK SILICONE 21g là silicon đen chuyên dụng chất lượng cao, tạo gioăng máy, làm kín các bề mặt. Chịu nhiệt độ lên đến 350oC. Đáp ứng các yêu cầu kỹ thuật của các nhà sản xuất ô tô và linh kiện gốc (OEM).Sản phẩm được dùng thay thế gioăng máy ô tô bằng các chất liệu như: giấy, amiang, cao su. Với công thức SENSOR SAFE, K2 Black Silicon an toàn với các cảm biến ô xi (lambda sensor) sử dụng trong các xe đời mới có phun nhiên liệu điện tử. Ngoài ra, sản phẩm còn có thể dùng cho nhu cầu khác khi cần làm kín và chịu nhiệt độ cao như: van, mặt bích, rơ le nhiệt, bọc trục cam, máy bơm…
Đặc tính sản phẩm: • Bảo đảm dính chặt, bền chắc, không xì và luôn mềm dẻo,lấp đầy những lỗ hổng.• Chống lại sự tác động của nước, dầu, axit và những chất hóa học khác.• Chịu được rung động mạnh, không lão hóa.
Hướng dẫn sử dụng:6. Làm sạch, khô bề mặt khỏi bụi bẩn, dầu mỡ, dấu vết gioăng cũ7. Tra đều, liên tục một lượng vừa đủ silicon lên bề mặt8. Loại bỏ chỗ thừa bằng dao sắc (dao nhúng trong nước xà phòng)9. Để khô silicone: bắt đầu khô sau 5 phút, 1h sau sẽ chịu được chạm nhẹ, sau 24h sẽ khô hoàn toàn.10. Cắt bỏ chỗ thừa sau khi đông cứng bằng dao sắc
Đóng gói: Tuýp 21g
Xuất xứ: EU (Ba Lan), do OTOFIX nhập khẩu trực tiếp![Qre7BB39pLFSSXK3rFB9.jpg](http://media3.scdn.vn/img4/2021/09_22/Qre7BB39pLFSSXK3rFB9.jpg)
![0yvUaIP5lk6eWodDpeHc.jpg](http://media3.scdn.vn/img4/2021/09_22/0yvUaIP5lk6eWodDpeHc.jpg)
![euD4RAHTyGZuOryWJGJX.jpg](http://media3.scdn.vn/img4/2021/09_22/euD4RAHTyGZuOryWJGJX.jpg)